DSpace@nitr >
National Institue of Technology- Rourkela >
Conference Papers >

Please use this identifier to cite or link to this item: http://hdl.handle.net/2080/1782

Full metadata record

DC FieldValueLanguage
contributor.authorKarak, S K-
contributor.authorMajumdar, J D-
contributor.authorLojkowski, W-
contributor.authorManna, I-
identifier.citationNMD-ATM 2012, Tata Steel, Jamshedpur, 16-19th November 2012en
descriptionCopyright belongs to proceeding publisheren
description.abstractIn this present work, an attempt has been made to synthesize of elemental powder blend of 83.0Fe-13.5Cr-2.0Al-0.5Ti (alloy A), 79.0Fe-17.5Cr-2.0Al-0.5Ti(alloy B), 75.0Fe-21.5Cr-2.0Al-0.5Ti(alloy C), and 71.0Fe-25.5Cr-2.0Al-0.5Ti (alloy D), alloys with 1.0 nano-Y2O3 (all in wt %) dispersion by solid state mechanical alloying route and consolidate milled powder by different sintering methods high pressure sintering (HPS), hot isostatic pressing (HIP)[1, 2], pulse plasma sintering (PPS)[3],and hydrostatic extrusion (HE) etc). Following this mechano-chemical synthesis and consolidation, extensive effort has been undertaken to characterize the microstructural evolution by X-ray diffraction, scanning and transmission electron microscopy, scanning tunneling electron microscopy, energy disperse spectroscopy and asses mechanical properties including hardness, compressive strength, Young’s modulus, fracture toughness. The details synthesis and characterization was reported recently in Karak et al. [1,2, 3].The present ferritic alloys record extraordinary levels of compressive strength (summarized at Table-1) (2012-3325 MPa), yield strength (525-1626 MPa), Young’s modulus (240-290 GPa), and hardness (15.5-19.7 GPa) and measure up to 2-3 times greater strength than other oxide dispersion strengthen ferritic steel (ODS steel) (< 1200 MPa) and higher than tungsten based alloys (< 2200 MPa) in strength but at a lower density (~ 7.4 Mg/m3). The novelty of these alloys lies in the unique microstructure and uniform distribution (shown in Figs. 1(a-b)) of either nanomertic (10-20 nm) oxide (Y2Ti2O7 or Y2O3) or intermetallic (Fe11TiY and Al9.22Cr2.78Y phase aggregates (Figs. 1(a-c)) along the grain boundary (Fig. 2a) which causes the grain boundary pinning, resulting high hardness and high compressive strength by annealing after mechanical alloying (MA) under ambient condition using high energy planetary ball milling. Thus, the above results suggest that mechanical alloying followed by high pressure sintering (HPS), pulse plasma sintering (PPS),hot isostatic pressing (HIP) and hydostatic extrusion (HE) etc are a flexible, convenient and promising route for synthesizing ferritic alloys with nano-oxide dispersed matrix offering attractive mechanical properties.en
format.extent4912931 bytes-
subjectNano-Y2O3 dispersed ferritic steelen
subjectMechanical alloyingen
subjectHigh Pressure Sinteringen
subjectHot Isostatic Pressingen
subjectPulse Palsma Sinteringen
subjectHydrostatic Extrusionen
subject; Mechanical Propertiesen
titleDevelopment of Nano-Y2O3 Dispersed Ferritic Alloys for Nuclear Reactorsen
Appears in Collections:Conference Papers

Files in This Item:

File Description SizeFormat
NMD-ATM-2012.pdf4797KbAdobe PDFView/Open

Show simple item record

All items in DSpace are protected by copyright, with all rights reserved.


Powered by DSpace Feedback